32.13. FQ-PIE queue disc

This chapter describes the FQ-PIE ([Ram19]) queue disc implementation in ns-3.

The FQ-PIE queue disc combines the Proportional Integral Controller Enhanced (PIE) AQM algorithm with the FlowQueue scheduler that is part of FQ-CoDel (also available in ns-3). FQ-PIE was introduced to Linux kernel version 5.6.

32.13.1. Model Description

The source code for the FqPieQueueDisc is located in the directory src/traffic-control/model and consists of 2 files fq-pie-queue-disc.h and fq-pie-queue-disc.cc defining a FqPieQueueDisc class and a helper FqPieFlow class. The code was ported to ns-3 based on Linux kernel code implemented by Mohit P. Tahiliani.

This model calculates drop probability independently in each flow queue. One difficulty, as pointed out by [CableLabs14], is that PIE calculates drop probability based on the departure rate of a (flow) queue, which may be more highly variable than the aggregate queue. An alternative, which CableLabs has called SFQ-PIE, is to calculate an overall drop probability for the entire queue structure, and then scale this drop probability based on the ratio of the queue depth of each flow queue compared with the depth of the current largest queue. This ns-3 model does not implement the SFQ-PIE variant described by CableLabs.

32.13.1.1. References

Ram19

  1. Ramakrishnan, M. Bhasi, V. Saicharan, L. Monis, S. D. Patil and M. P. Tahiliani, “FQ-PIE Queue Discipline in the Linux Kernel: Design, Implementation and Challenges,” 2019 IEEE 44th LCN Symposium on Emerging Topics in Networking (LCN Symposium), Osnabrueck, Germany, 2019, pp. 117-124,

CableLabs14

  1. White, Active Queue Management in DOCSIS 3.X Cable Modems, CableLabs white paper, May 2014.

32.13.1.2. Attributes

The key attributes that the FqPieQueue class holds include the following. First, there are PIE-specific attributes that are copied into the individual PIE flow queues:

  • UseEcn: Whether to use ECN marking

  • MarkEcnThreshold: ECN marking threshold (RFC 8033 suggests 0.1 (i.e., 10%) default).

  • UseL4s: Whether to use L4S (only mark ECT1 packets at CE threshold)

  • MeanPktSize: Constant used to roughly convert bytes to packets

  • A: Alpha value in PIE algorithm drop probability calculation

  • B: Beta value in PIE algorithm drop probability calculation

  • Tupdate: Time period to calculate drop probability

  • Supdate: Start time of the update timer

  • DequeueThreshold: Minimum queue size in bytes before dequeue rate is measured

  • QueueDelayReference: AQM latency target

  • MaxBurstAllowance: AQM max burst allowance before random drop

  • UseDequeueRateEstimator: Enable/Disable usage of Dequeue Rate Estimator

  • UseCapDropAdjustment: Enable/Disable Cap Drop Adjustment feature mentioned in RFC 8033

  • UseDerandomization: Enable/Disable Derandomization feature mentioned in RFC 8033

Second, there are QueueDisc level, or FQ-specific attributes:: * MaxSize: Maximum number of packets in the queue disc * Flows: Maximum number of flow queues * DropBatchSize: Maximum number of packets dropped from the fat flow * Perturbation: Salt value used as hash input when classifying flows * EnableSetAssociativeHash: Enable or disable set associative hash * SetWays: Size of a set of queues in set associative hash

32.13.1.3. Examples

A typical usage pattern is to create a traffic control helper and to configure the type and attributes of queue disc and filters from the helper. For example, FqPIE can be configured as follows:

TrafficControlHelper tch;
tch.SetRootQueueDisc("ns3::FqPieQueueDisc",
                     "DropBatchSize", UintegerValue(1)
                     "Perturbation", UintegerValue(256));
QueueDiscContainer qdiscs = tch.Install(devices);

32.13.2. Validation

The FqPie model is tested using FqPieQueueDiscTestSuite class defined in src/test/ns3tc/fq-pie-queue-test-suite.cc.

The tests are similar to the ones for FqCoDel queue disc mentioned in first section of this document. The test suite can be run using the following commands:

$ ./ns3 configure --enable-examples --enable-tests
$ ./ns3 build
$ ./test.py -s fq-pie-queue-disc

or:

$ NS_LOG="FqPieQueueDisc" ./ns3 run "test-runner --suite=fq-pie-queue-disc"